Hi guys,
tonight I discovered that my Nord Stage 3 compact doesn't work properly. The 4th C#-Key works only with Organ-Engine. When using Piano- or Synth-Section or even extern section the Key doesn't work at all. I have absolutely no idea. But I have made a short clip with my mobile phone: https://share.icloud.com/photos/08V8JFp ... ZI7PWOavEg
Firmware is 2.54.
Maybe anyone got an idea?
Thank you!
Holger
Issue with 4th C#
- Schorsch
- Moderator
- Posts: 2599
- Joined: 15 May 2018, 23:34
- 7
- Your Nord Gear #1: Nord Stage 3
- Your Nord Gear #2: Nord Stage 3
- Location: Germany - NRW
- Has thanked: 1481 times
- Been thanked: 939 times
Re: Issue with 4th C#
Hi Holger,
you might have some dirt under the contacts of that key - have you set the B3 Organ trigger point to high in the systems settings? That could explain why just the organ responds when you press the key since the dirt may sit below the contact for low trigger points which are used for the other engines if I’m correct. If that’s the case you would have to clean the contacts, there are some thread in the forum describing the procedure
you might have some dirt under the contacts of that key - have you set the B3 Organ trigger point to high in the systems settings? That could explain why just the organ responds when you press the key since the dirt may sit below the contact for low trigger points which are used for the other engines if I’m correct. If that’s the case you would have to clean the contacts, there are some thread in the forum describing the procedure
Regards Schorsch
Check this https://chris55.github.io/ns3-program-viewer/ awesome tool to visualize NS2/3 programs and re-create them on the other instrument!
Gear: NS3C, Uhl X4V-1, 2-manual HX3.4 organ made by Tastendoktor, SL88 Studio
Check this https://chris55.github.io/ns3-program-viewer/ awesome tool to visualize NS2/3 programs and re-create them on the other instrument!
Gear: NS3C, Uhl X4V-1, 2-manual HX3.4 organ made by Tastendoktor, SL88 Studio
-
- Posts: 10
- Joined: 21 Aug 2017, 02:38
- 8
- Your Nord Gear #1: Nord Stage 3
- Your Nord Gear #2: Nord Piano 4
- Has thanked: 5 times
- Been thanked: 1 time
Re: Issue with 4th C#
Hi Schorsch,Schorsch wrote:Hi Holger,
you might have some dirt under the contacts of that key - have you set the B3 Organ trigger point to high in the systems settings? That could explain why just the organ responds when you press the key since the dirt may sit below the contact for low trigger points which are used for the other engines if I’m correct. If that’s the case you would have to clean the contacts, there are some thread in the forum describing the procedure
thanks so far. I don't remember changing any trigger point. Even don't know how to. But will try to clean the contacts.
Holger
Nord Stage 3 compact
Roland Integra 7
Roland Integra 7
- Schorsch
- Moderator
- Posts: 2599
- Joined: 15 May 2018, 23:34
- 7
- Your Nord Gear #1: Nord Stage 3
- Your Nord Gear #2: Nord Stage 3
- Location: Germany - NRW
- Has thanked: 1481 times
- Been thanked: 939 times
Re: Issue with 4th C#
Hi,
just sent you a PM ….
Information on how to open the keybed and clean the contacts can be found here for example: nord-stage-forum-f3/note-lost-sensitivi ... is#p130858
just sent you a PM ….
Information on how to open the keybed and clean the contacts can be found here for example: nord-stage-forum-f3/note-lost-sensitivi ... is#p130858
Last edited by Schorsch on 25 Aug 2021, 00:29, edited 1 time in total.
Regards Schorsch
Check this https://chris55.github.io/ns3-program-viewer/ awesome tool to visualize NS2/3 programs and re-create them on the other instrument!
Gear: NS3C, Uhl X4V-1, 2-manual HX3.4 organ made by Tastendoktor, SL88 Studio
Check this https://chris55.github.io/ns3-program-viewer/ awesome tool to visualize NS2/3 programs and re-create them on the other instrument!
Gear: NS3C, Uhl X4V-1, 2-manual HX3.4 organ made by Tastendoktor, SL88 Studio