NS3 Bug reports etc.

[DJKeys]

Its just good to have that information in these reports so we can see if certain issues can be directly related to specific OS versions, thanks!

-dj

[OldTomCat]

Hi hope someone can help with this.
Just bought a triple pedal for my NS3 to catch and hold some pads but annoyingly it wont hold the organ (synth + piano engines are caught and held ok). The sustain pedal holds the organ perfectly!!! So why doesn't the sostenuto do the same???

[Mr_-G-]

Is the Sustain switched on in the organ section?

[aureliopenna]

Is the sustenuto function working on pianos?

[Satomy]

Hi, have you noticed any improvements with the 1.36 update? I still have the following problems:
1- if I use slot B in dual kB mode, the swell pedal does not work, it does not send midi parameters to the connected keyboard and destined to slot B, if I play the organ section directly on the NS 3, the Shell pedal works correctly. Pedal CTRL (EXpression) does not work, either in dual KB or directly on NS3.
2- Problem of MIDI controls: MIDI CC 11 Ctrl Pedal (expression) and all effects controls from MIDI CC from 82 to MIDI CC 119 (enable 1, type eff1, source eff.1, quantity eff.1, eff.1 rate, eff 2 Type, etc. .. etc. .. etc. Do not work, NS3 does not receive the midi controls assigned by the midi keyboard in which it is connected?

[maurich]

My 6th end 8th drawbar stuck in the ''1'' position on my Compact 3. I put drawbars to the end, but I hear that one position out, and see on the display number 1. so, if I want classic 888000000 position, I cannot. Just 888001010... anybody with same problem? Software bug or???

[baekgaard]

My 6th end 8th drawbar stuck in the ''1'' position on my Compact 3. I put drawbars to the end, but I hear that one position out, and see on the display number 1. so, if I want classic 888000000 position, I cannot. Just 888001010... anybody with same problem? Software bug or???

Sounds more like a hardware issue to me than anything software related. I'm not sure if there is a "recalibration" procedure for the sliders, but it's probably a good idea to call back to your dealer to check what's up with the drawbars.

Do you have any organs saved with a preset of xxxxx0000? If so, when you load then up, do they stay at 0 until you start moving/touching the drawbars?

[maurich]

My 6th end 8th drawbar stuck in the ''1'' position on my Compact 3. I put drawbars to the end, but I hear that one position out, and see on the display number 1. so, if I want classic 888000000 position, I cannot. Just 888001010... anybody with same problem? Software bug or???

Sounds more like a hardware issue to me than anything software related. I'm not sure if there is a "recalibration" procedure for the sliders, but it's probably a good idea to call back to your dealer to check what's up with the drawbars.

Do you have any organs saved with a preset of xxxxx0000? If so, when you load then up, do they stay at 0 until you start moving/touching the drawbars?

Yes, i try this solution. When i move my drawbars, it stucks on 1. I think IT IS hardware issue. Do you have some advice how to recalibrate that?

[fREDkeys]

My 6th end 8th drawbar stuck in the ''1'' position on my Compact 3. I put drawbars to the end, but I hear that one position out, and see on the display number 1. so, if I want classic 888000000 position, I cannot. Just 888001010... anybody with same problem? Software bug or???

I recently ran into a situation like this which is just possibly (and hopefully) what is happening to you.

In my case, there was a morph assigned to the drawbar settings which was preventing them from behaving entirely normally. I cleared all the morphs and my drawbars stopped misbehaving.

[maurich]

My 6th end 8th drawbar stuck in the ''1'' position on my Compact 3. I put drawbars to the end, but I hear that one position out, and see on the display number 1. so, if I want classic 888000000 position, I cannot. Just 888001010... anybody with same problem? Software bug or???

I recently ran into a situation like this which is just possibly (and hopefully) what is happening to you.

In my case, there was a morph assigned to the drawbar settings which was preventing them from behaving entirely normally. I cleared all the morphs and my drawbars stopped misbehaving.

Unoftunatelly, this is not my case...I'm gonna do factory reset, this is last step of hope...