MIDI channel separation to Piano Module
-
- Posts: 66
- Joined: 21 May 2013, 14:28
- 10
- Your Nord Gear #1: Nord C2D
- Has thanked: 1 time
- Been thanked: 12 times
MIDI channel separation to Piano Module
C2D MIDI channel defaults (Ch 1 - upper, Ch 2 - lower, Ch 3 - 1st 2 octaves on lower when selecting 'Pedal To Great'). I MIDI connected to a piano tone module, set it to MIDI Channel 2 - hoping to control it strictly by lower manual (upper section). Result is, both upper manual and both sections of lower manual manual trigger sound on the module. Interestingly, when I change patches on the module, only the notes played on the lower manual translate to the 'new' sound. Upper manual continues to just play patch 1. Any thoughts ? I'm about to return the piano module, thinking it just doesn't interface well with the C2D. Just wanted to see if there was a MIDI setting I was missing on the C2D?
- maxpiano
- Patch Creator
- Posts: 6272
- Joined: 27 Jun 2011, 13:29
- 12
- Your Nord Gear #1: Nord Stage 3
- Location: Italy
- Has thanked: 448 times
- Been thanked: 2197 times
Re: MIDI channel separation to Piano Module
Which piano module is it? from your description it sounds like it is multitimbral and so receiving on multiple channels...
-
- Posts: 66
- Joined: 21 May 2013, 14:28
- 10
- Your Nord Gear #1: Nord C2D
- Has thanked: 1 time
- Been thanked: 12 times
Re: MIDI channel separation to Piano Module
S-Engine MIDI PLUS. Very similar to the Pianobox II. Has a "channel" selection button that allows you to specify channel. So, I'm thinking "not" multitimbral, right ?
- maxpiano
- Patch Creator
- Posts: 6272
- Joined: 27 Jun 2011, 13:29
- 12
- Your Nord Gear #1: Nord Stage 3
- Location: Italy
- Has thanked: 448 times
- Been thanked: 2197 times
Re: MIDI channel separation to Piano Module
MIDIPLUS S-Engine, E-MU 8030-based sound-engine with 128-voice polyphony Over 192 built in sounds featuring 64 custom E-MU classic keys programs and a full GM bank with drums 128-voice polyphony 16-part multitimbral synthesizer Reverb and Chorus effects 4-segment display, hi-Z guitar input (1/4" jack), play/stop button, 10 key buttons, MIDI I/O, line out (1/4" jack), headphone output (mini-jack), USB Connection.
Now repeat the mantra : "RTFM is not an offense, is a good friendly advice"
Now repeat the mantra : "RTFM is not an offense, is a good friendly advice"
Last edited by maxpiano on 28 Feb 2017, 01:22, edited 1 time in total.
-
- Posts: 66
- Joined: 21 May 2013, 14:28
- 10
- Your Nord Gear #1: Nord C2D
- Has thanked: 1 time
- Been thanked: 12 times
Re: MIDI channel separation to Piano Module
True Dat! My miss. OK so,,,,, (demonstrating my MIDI challenged brain) .. What's the use of the the MIDI Channel selector for? How then can I use that or any other piano module, (assuming they're all likely multi - T), and send note messages "ONLY" from the C2D lower manual (upper octaves)?? (Channel 2) .
- harmonizer
- Posts: 509
- Joined: 25 Dec 2012, 17:10
- 11
- Your Nord Gear #1: Nord Stage 3
- Your Nord Gear #2: Nord Electro 3
- Location: NJ, USA
- Has thanked: 72 times
- Been thanked: 128 times
Re: MIDI channel separation to Piano Module
To figure out what the MIDI Channel selector is for, I would need to read the manual. I tried but was not able to locate a copy of the manual online. The "midiplus.com" web site is considered unsafe by my PC's security product, so I am not going to look there. I found a manual for the Pianobox product from a German web site, but that does not seem to be the correct product.
- maxpiano
- Patch Creator
- Posts: 6272
- Joined: 27 Jun 2011, 13:29
- 12
- Your Nord Gear #1: Nord Stage 3
- Location: Italy
- Has thanked: 448 times
- Been thanked: 2197 times
Re: MIDI channel separation to Piano Module
For the first question, you should check the manual; for the second, simply set all other parts to Channels other than 1,2,3 (or switch them off, if possible, again see what the manual says about it).The Franchise wrote:True Dat! My miss. OK so,,,,, (demonstrating my MIDI challenged brain) .. What's the use of the the MIDI Channel selector for? How then can I use that or any other piano module, (assuming they're all likely multi - T), and send note messages "ONLY" from the C2D lower manual (upper octaves)?? (Channel 2) .
If that module is not flexible enough to allow those settings, consider buying a different one that is single channel/part and/or allows that flexibility (check the specs and manual before buying).
Last option, put a MIDI filter (dedicated box or via a Computer/iPad) in between that will block MIDI messages of all channels except 2.
-
- Posts: 66
- Joined: 21 May 2013, 14:28
- 10
- Your Nord Gear #1: Nord C2D
- Has thanked: 1 time
- Been thanked: 12 times
Re: MIDI channel separation to Piano Module
Hey thanks all the thoughts put into this, Max. The manual was as useless as the online site info. Bottom line - The unit would be a good, inexpensive addition to someone looking to grab GM sounds. But for my application - NFG.
Best!
Best!
- maxpiano
- Patch Creator
- Posts: 6272
- Joined: 27 Jun 2011, 13:29
- 12
- Your Nord Gear #1: Nord Stage 3
- Location: Italy
- Has thanked: 448 times
- Been thanked: 2197 times
Re: MIDI channel separation to Piano Module
I do think so too, maybe it's time for you to go and get some FG one!The Franchise wrote:Hey thanks all the thoughts put into this, Max. The manual was as useless as the online site info. Bottom line - The unit would be a good, inexpensive addition to someone looking to grab GM sounds. But for my application - NFG.
Best!
Last edited by maxpiano on 28 Feb 2017, 22:36, edited 2 times in total.