Thanks all, it appears to be my physical Compact 73 mod wheel not working fully.
In the "Electrified MW" factory patch, B3 drawbars are morphed to be drawn out via the mod wheel. They draw to full position when the mod wheel is all the way up on the NS3 HP76. They only come up part way on my compact 73.
Can anyone replicate this so I know it's just my Compact and not a firmware issue? Thx!
13 posts
• Page 2 of 2 • 1, 2
- darrylhebert
- Posts: 10
- Joined: 23 Apr 2018, 21:58
- Country:
- Has thanked: 11 times
- Been thanked: 0 time
- Your Nord Gear #1: Nord Stage 3
Re: NS3 Compact - mod wheel vibrato not working
darrylhebert wrote:Thanks all, it appears to be my physical Compact 73 mod wheel not working fully.
In the "Electrified MW" factory patch, B3 drawbars are morphed to be drawn out via the mod wheel. They draw to full position when the mod wheel is all the way up on the NS3 HP76. They only come up part way on my compact 73.
Can anyone replicate this so I know it's just my Compact and not a firmware issue? Thx!
Works as you described on my HP76 like yours. This is actually better news than if only the Vibrato was the problem as the MW can easily be replaced. I would still try an older OS just to rule that out. Good luck.
Last edited by WannitBBBad on 03 Sep 2021, 19:03, edited 1 time in total.
Nord Stage 3 | SC Prophet T8 | Korg X50... In the past: Nord Stage EX, 2, 2EX | SC Prophet 5, 10 | MiniMoog | Hammond B3 & 122 Leslie | Yamaha DX7IIFD, EX5, CP60 | Hohner D6 | Fender Rhodes | Roland S-50, D-50, XP-50...
- The author WannitBBBad was thanked by:
- darrylhebert
-
WannitBBBad - Patch Creator
- Posts: 1807
- Joined: 25 Jul 2011, 03:36
- Country:
- Has thanked: 1048 times
- Been thanked: 1530 times
- Your Nord Gear #1: Nord Stage 3
Re: NS3 Compact - mod wheel vibrato not working
While replacing the pitchstick on this NS3C/SW73 I did remove the mod wheel edge connector which clips on to the circuit board.If this was my issue,would load older OS and try again before 'popping the hood' to verify the mod wheel connector is not just partially connected.
With the old pitchstick still connected to verify cable placement for the new one,a cable did 'give away' from the 'stick' end of the well used device.
How much you want to bet it was just a loose cable? Have another new spare just in case. In almost fifty years never had a controller fail on my Rolands.
Make sure the edge connector is 100% connected from that mod wheel to the circuit board.
With the old pitchstick still connected to verify cable placement for the new one,a cable did 'give away' from the 'stick' end of the well used device.
How much you want to bet it was just a loose cable? Have another new spare just in case. In almost fifty years never had a controller fail on my Rolands.
Make sure the edge connector is 100% connected from that mod wheel to the circuit board.
NS3C NS2EX88 C2D Yamaha MOX8 Behringer Model D (5) Behringer Neutron (5) Roland Lucina AX9 12 Hammonds/Leslies.(BV/BCV/B2/3 A100's/M3/M102 etc.
- The author LeftyBass68 was thanked by:
- WannitBBBad
- LeftyBass68
- Posts: 289
- Joined: 10 Jul 2018, 03:58
- Location: Vancouver
- Country:
- Has thanked: 64 times
- Been thanked: 68 times
- Your Nord Gear #1: Nord Stage 2 EX
- Your Nord Gear #2: Nord Stage 3
13 posts
• Page 2 of 2 • 1, 2
Who is online
Users browsing this forum: No registered users and 33 guests