7 posts
• Page 1 of 1
Rotary pedal serving C2D
I want to use rotary control pedal to switch rotary from slow when not pressing pedal to fast when pressing pedal. (I’m using a sustain pedal) Only when I press the pedal I want the rotary in fast mode. Is it possible?
- Figman
- Posts: 4
- Joined: 18 Dec 2022, 16:43
- Country:
- Has thanked: 0 time
- Been thanked: 0 time
Re: Rotary pedal serving C2D
From C2D manual:
Rotor Pedal Mode
If you are using a sustain pedal connected to control Rotor Speed this allows you to set how this should operate . “Hold” means that the Rotor Speed is fast for as long as the pedal is down and reverts back to slow/stopped when the pedal is released (or vice versa depending on the set pedal polarity) .
“Toggle” means that the fast & slow/stopped rotor speed is cycled each time you activate the pedal, like an on/off switch pedal .
Range: Hold, (default), Toggle.
So check that the setting is Hold and that pedal Polarity (type) setting is correct for your sustain,
Rotor Pedal Mode
If you are using a sustain pedal connected to control Rotor Speed this allows you to set how this should operate . “Hold” means that the Rotor Speed is fast for as long as the pedal is down and reverts back to slow/stopped when the pedal is released (or vice versa depending on the set pedal polarity) .
“Toggle” means that the fast & slow/stopped rotor speed is cycled each time you activate the pedal, like an on/off switch pedal .
Range: Hold, (default), Toggle.
So check that the setting is Hold and that pedal Polarity (type) setting is correct for your sustain,
Last edited by maxpiano on 18 Dec 2022, 18:00, edited 1 time in total.
-
maxpiano - Patch Creator
- Posts: 6243
- Joined: 27 Jun 2011, 13:29
- Location: Italy
- Country:
- Has thanked: 447 times
- Been thanked: 2194 times
- Your Nord Gear #1: Nord Stage 3
Re: Rotary pedal serving C2D
That's how it works so problem must be somewhere else: what is the brand and model of your sustain pedal? Have you tried with different pedals?
Last edited by maxpiano on 18 Dec 2022, 18:08, edited 1 time in total.
-
maxpiano - Patch Creator
- Posts: 6243
- Joined: 27 Jun 2011, 13:29
- Location: Italy
- Country:
- Has thanked: 447 times
- Been thanked: 2194 times
- Your Nord Gear #1: Nord Stage 3
Re: Rotary pedal serving C2D
Yes tried several. But I’m in the menu of Rotary Control. Type:closed, open, half moon. And next: rotary pedal, hold/toggle
Is that the menu or somewhere else?
Is that the menu or somewhere else?
- Figman
- Posts: 4
- Joined: 18 Dec 2022, 16:43
- Country:
- Has thanked: 0 time
- Been thanked: 0 time
Re: Rotary pedal serving C2D
Figman wrote:Yes tried several. But I’m in the menu of Rotary Control. Type:closed, open, half moon. And next: rotary pedal, hold/toggle
Is that the menu or somewhere else?
That's the right menu.
Type: closed or open (depends on which pedal you are using, try both)
Rotary Pedal: hold
Note: assuming you are using a momentary switch i.e. a "sustain pedal" and not an on/off switch instead, of course. If still not working you may have a problem with your C2D Rotary Pedal jack input.
Last edited by maxpiano on 18 Dec 2022, 21:24, edited 1 time in total.
-
maxpiano - Patch Creator
- Posts: 6243
- Joined: 27 Jun 2011, 13:29
- Location: Italy
- Country:
- Has thanked: 447 times
- Been thanked: 2194 times
- Your Nord Gear #1: Nord Stage 3
7 posts
• Page 1 of 1
Return to Nord C1 / C2 / C2D Organ Forum
Who is online
Users browsing this forum: No registered users and 20 guests