I have a CPS Spacestation v3.
When I plug the TS audio cables from the Nord directly to the Spacestation amp, the sound is noticeably superior then when I go through a Mackie mixer OR a Radial JDI Direct box
The Radial JDI direct box is equipped with Jensen transformers which are supposedly the "best". It also has THRU outputs, and I'm using another pair of good quality unbalanced cables to connect the Radial JDI to the amp. Basically the Direct box is acting just as an adapter or extension in this case (but normally I'd use it to send a balanced mix to FOH, and the THRU ports for my personal monitor)
On the other hand, the mackie mixer is equipped with their new Vita preamps which are supposedly great quality also.
Question is, why is this happening (why is sound degrading)? The THRU port on the Direct box, shouldn't that just send an untouched duplicate original signal?
And I'm positive that the sound "degrades" somewhat, it seems richer and fuller when I connect my Nord directly to the amp
Oh, and this happens to every other keyboard as well (so this doesn't necessary apply only to the Nord).
My TS cable lengths are pretty short.
9 posts
• Page 1 of 1
Sound quality - connecting directly from amp vs mixer/DI
Last edited by emediately on 10 Mar 2016, 00:48, edited 1 time in total.
- emediately
- Posts: 8
- Joined: 17 Feb 2016, 01:43
- Country:
- Has thanked: 0 time
- Been thanked: 0 time
- Your Nord Gear #1: Nord Electro 5
Re: Sound quality - connecting directly from amp vs mixer/DI
Hi,
a high-Z input may give a better bass response, compared to a low-Z input, because the DC decoupling caps in the output act as highpass filter.
The corner frequency (3 dB/octave) is 1/(2 pi RC).
As long as R is high it affects only earthquake frequencies, but lower R ("Z") will move the cutoff frequency into the audible range.
For example, an assumed 10uF coupling cap into a 10kOhms input forms a 1.6 Hz highpass, which is as good as a wire.
The same source into a 100 ohms input moves the corner freq to 160 Hz, which will have a very audible impact on the signal.
This is just a possible explanation.
a high-Z input may give a better bass response, compared to a low-Z input, because the DC decoupling caps in the output act as highpass filter.
The corner frequency (3 dB/octave) is 1/(2 pi RC).
As long as R is high it affects only earthquake frequencies, but lower R ("Z") will move the cutoff frequency into the audible range.
For example, an assumed 10uF coupling cap into a 10kOhms input forms a 1.6 Hz highpass, which is as good as a wire.
The same source into a 100 ohms input moves the corner freq to 160 Hz, which will have a very audible impact on the signal.
This is just a possible explanation.
And I was worried - all the way down to the ground
When it comes to holding safety nets
Nobody seems to be around
When it comes to holding safety nets
Nobody seems to be around
-
offrhodes - Posts: 150
- Joined: 12 Dec 2015, 21:33
- Location: Munich, Germany
- Country:
- Has thanked: 17 times
- Been thanked: 30 times
- Your Nord Gear #1: Nord Stage 2 EX
- Your Nord Gear #2: Nord Electro 5
Re: Sound quality - connecting directly from amp vs mixer/DI
How do you set the pan in the channels of your instrument when playing thought the mixer? They should be kept separated, (i.e. panned in opposite directions). If you have both channels the middle, that is mixing the output into a mono signal, and the ss3 will not be able to make its simulated stereo trick.
-
Mr_-G- - Moderator
- Posts: 4617
- Joined: 18 Aug 2012, 16:48
- Has thanked: 1475 times
- Been thanked: 1257 times
- Your Nord Gear #1: Nord Stage 2
Re: Sound quality - connecting directly from amp vs mixer/DI
(accidental duplicate post by editing)
Last edited by offrhodes on 12 Mar 2016, 09:01, edited 1 time in total.
And I was worried - all the way down to the ground
When it comes to holding safety nets
Nobody seems to be around
When it comes to holding safety nets
Nobody seems to be around
-
offrhodes - Posts: 150
- Joined: 12 Dec 2015, 21:33
- Location: Munich, Germany
- Country:
- Has thanked: 17 times
- Been thanked: 30 times
- Your Nord Gear #1: Nord Stage 2 EX
- Your Nord Gear #2: Nord Electro 5
Re: Sound quality - connecting directly from amp vs mixer/DI
I think Mr G's suspect - stereo - may very well be the culprit. If you're using the Radial Duplex model, you should check the settings of the Mono switches.
- RedLeo
- Patch Creator
- Posts: 1558
- Joined: 07 Aug 2011, 02:08
- Has thanked: 140 times
- Been thanked: 702 times
Re: Sound quality - connecting directly from amp vs mixer/DI
I just bought CPS V3. I plugged my Stage 2 EX to SS3 in diffrent ways: directly, thorugh the mixer and through my interface. Every time when i play something (no matter what instrument) the side speaker of the SS3 generates a large amount of distortion . Is that normal?
Last edited by AnEarthquake on 07 Jul 2017, 18:46, edited 1 time in total.
Keys: Nord Stage 2 EX Compact, Nord Electro 3 61, Yamaha Motif ES6
PA: 2 x RCF Art 722-A, CPS Spacestation v3
PA: 2 x RCF Art 722-A, CPS Spacestation v3
-
AnEarthquake - Posts: 12
- Joined: 30 Mar 2012, 13:24
- Country:
- Has thanked: 0 time
- Been thanked: 1 time
- Your Nord Gear #1: Nord Stage 2 EX
- Your Nord Gear #2: Nord Electro 3
Re: Sound quality - connecting directly from amp vs mixer/DI
Not normal. The SSv3 is especially sensitive to cable issues. Even the smallest amount of dirt in one signal path will be dramatically amplified by the side-firing speaker. Start by swapping out your audio cables, then go from there.
I think I have gear issues ....
-
cphollis - Posts: 1592
- Joined: 01 Mar 2013, 20:56
- Location: Vero Beach, Fl
- Country:
- Has thanked: 58 times
- Been thanked: 706 times
- Your Nord Gear #1: Nord Stage 4
- Your Nord Gear #2: Nord Piano 5
Re: Sound quality - connecting directly from amp vs mixer/DI
My Spacestation was broken. I got a new one from Thomann. How to set up my Stage 2 EX with SSv3 properly? I noticed that when I set the volume on Stage at 3 o'clock and set the volume on SSv3 at 10 o'clock, the sound becomes clipped faster, than when I set the volume on both devices at 12 o'clock. Ps. Sorry for my English
Keys: Nord Stage 2 EX Compact, Nord Electro 3 61, Yamaha Motif ES6
PA: 2 x RCF Art 722-A, CPS Spacestation v3
PA: 2 x RCF Art 722-A, CPS Spacestation v3
-
AnEarthquake - Posts: 12
- Joined: 30 Mar 2012, 13:24
- Country:
- Has thanked: 0 time
- Been thanked: 1 time
- Your Nord Gear #1: Nord Stage 2 EX
- Your Nord Gear #2: Nord Electro 3
Re: Sound quality - connecting directly from amp vs mixer/DI
I just purchased the Radial Pro Key Largo... And it is fantastic!
3 stereo line inputs
1 USB in / out for Soft Synth (see recessed studio / live switch)
1 stereo effects buss
Midi In / Out for USB to Midi
Stereo XLR mains with level / ground lift
Stereo TRS for Stage monitoring with level / ground lift
https://youtu.be/vgiMACdVGDA
3 stereo line inputs
1 USB in / out for Soft Synth (see recessed studio / live switch)
1 stereo effects buss
Midi In / Out for USB to Midi
Stereo XLR mains with level / ground lift
Stereo TRS for Stage monitoring with level / ground lift
https://youtu.be/vgiMACdVGDA
NS4 / NS3 / NS-EX / Modular G1 / G2 / G2X / NL3
Basically Too Many Nords to Haul to a Gig
Basically Too Many Nords to Haul to a Gig
- Mr. Marko
- Posts: 176
- Joined: 08 Mar 2009, 19:15
- Has thanked: 7 times
- Been thanked: 44 times
- Your Nord Gear #1: Nord Stage 3
- Your Nord Gear #2: Nord Modular
9 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 31 guests