Just curious if anyone has a SNAGG loss protection microchip installed in their Nord board?
http://www.snagg.com/microchip-retrofit-kit-single-pack
http://www.americanmusical.com/Item--i-SNG-5020-LIST
-Ryan
8 posts
• Page 1 of 1
- Westside Ryan
- Posts: 67
- Joined: 27 Sep 2013, 20:44
- Country:
- Has thanked: 19 times
- Been thanked: 7 times
- Your Nord Gear #1: Nord C2D
Re: Anybody have a SNAGG loss protection microchip installed
Interesting. I you do decide to get one of those chips (the price seems okay for some peace of mind), it might be an idea to mount the chip on the inside of one of the wooden end cheeks. You could unscrew one, drill a small hole on the inside and glue the chip in - it would be invisible. Alternatively, you could even just use some decent quality tape to stick it to the inside of one of those wooden cheeks, but glueing (preferably in a small hole, which you can fill with glue) would be better.
- mjbrands
Re: Anybody have a SNAGG loss protection microchip installed
That's a good idea, but I think that the chip might have to be 2 to 3 inches deep in order to be read. I'll have to look into it some more.
- Westside Ryan
- Posts: 67
- Joined: 27 Sep 2013, 20:44
- Country:
- Has thanked: 19 times
- Been thanked: 7 times
- Your Nord Gear #1: Nord C2D
Re: Anybody have a SNAGG loss protection microchip installed
No, it wouldn't. With RFID more return signal is never a problem! Think of a guitar - it may be 2" deep inside the strap mount hole, but from the front or back it's less than 1" under the surface.
Personally I wouldn't screw it in the end cheek, as they might be replaced. Not sure where I would put it though!
Al
Personally I wouldn't screw it in the end cheek, as they might be replaced. Not sure where I would put it though!
Al
- Cornopean
- Patch Creator
- Posts: 119
- Joined: 18 May 2013, 12:52
- Country:
- Has thanked: 13 times
- Been thanked: 43 times
- Your Nord Gear #1: Nord Electro 4
- Your Nord Gear #2: Other Brand
Re: Anybody have a SNAGG loss protection microchip installed
In the product description it says "The chip should be positioned to allow 2-3 inches scanning distance".
If the 2-3 inches wouldn't matter, I think I would just super glue it to a corner of the metal housing.
If the 2-3 inches wouldn't matter, I think I would just super glue it to a corner of the metal housing.
- Westside Ryan
- Posts: 67
- Joined: 27 Sep 2013, 20:44
- Country:
- Has thanked: 19 times
- Been thanked: 7 times
- Your Nord Gear #1: Nord C2D
Re: Anybody have a SNAGG loss protection microchip installed
What I think that means is that it should be able to be within 2-3" of a scanner, so not buried 6" deep in a 12" solid cube. Either that or it should be somewhere that a scanner can get to externally with 2-3" of space around, i.e. not 2-3" from a surface the scanner can't physically get to. Both of these make sense to me electronically, which your first interpretation (of an admittedly unclear sentence!) didn't.
I'd check with the manufacturer and see if they had a recommendation for the Nord already. I'm going off theoretical understanding based on my electronics degree, rather than hands-on experience of the product.
I'd check with the manufacturer and see if they had a recommendation for the Nord already. I'm going off theoretical understanding based on my electronics degree, rather than hands-on experience of the product.
- Cornopean
- Patch Creator
- Posts: 119
- Joined: 18 May 2013, 12:52
- Country:
- Has thanked: 13 times
- Been thanked: 43 times
- Your Nord Gear #1: Nord Electro 4
- Your Nord Gear #2: Other Brand
Re: Anybody have a SNAGG loss protection microchip installed
Cornopean wrote:What I think that means is that it should be able to be within 2-3" of a scanner, so not buried 6" deep in a 12" solid cube. Either that or it should be somewhere that a scanner can get to externally with 2-3" of space around, i.e. not 2-3" from a surface the scanner can't physically get to. Both of these make sense to me electronically, which your first interpretation (of an admittedly unclear sentence.
Indeed. Scanner too close, just move it away from the item.
The closer the scanner is to the RFID chip, the easier it is to scan. This type of RFID chip is actually powered by a signal sent by the scanner, which is one of the reasons the scanner needs to be within a certain distance of the chip.
- mjbrands
Re: Anybody have a SNAGG loss protection microchip installed
Why don't they just say within 3"? I am now assuming that if you were 1/2" or 1" deep it would work fine right? The 2" to 3" made me think that it would have to be at least 2" deep, but not more than 3"!
- Westside Ryan
- Posts: 67
- Joined: 27 Sep 2013, 20:44
- Country:
- Has thanked: 19 times
- Been thanked: 7 times
- Your Nord Gear #1: Nord C2D
8 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 25 guests