- sent keyboard velocity messages with the Keyboard Trig Mode set to High
- placed the reverberation module after the rotary simulation module in the effects chain
- stored the synth bass pluck setting with a preset
6 posts
• Page 1 of 1
I wish the C2D ... (SW update?)
- elseif
- Posts: 22
- Joined: 20 Jun 2015, 21:25
- Country:
- Has thanked: 0 time
- Been thanked: 4 times
- Your Nord Gear #1: Nord C2D
- Your Nord Gear #2: Nord Electro 4
Re: I wish the C2D ... (SW update?)
Yes, why not, if it comes as well with the same update for the C2..Like they did with the last C2D update...
Stage 2/C2/NL2X+TC Pedals, 2XMatrix, EMU P2K, TX802, DSI P8/Tetra+H9, P12+TC HoF, D50+PG1000, XV5080,AX keytar, Streichfett, Drumbrute.Ibanez SR1200 & 2605 basses, Artstar AS153,G&L L2000,Legacy HSS,Asat Blueboys,Asat Deluxe Savanna.genelec 8040A.
-
Quai34 - Posts: 1874
- Joined: 01 Jan 2012, 23:02
- Location: CANADA WINNIPEG
- Country:
- Has thanked: 114 times
- Been thanked: 305 times
- Your Nord Gear #1: Nord Stage 2
- Your Nord Gear #2: Nord Lead 1/2/2x
Re: I wish the C2D ... (SW update?)
I third the motion.
It would be interesting to hear from a product manager as to whether it's possible to write firmware to place the reverberation module after the rotary simulation module in the effects chain.
I'm also interested in keyboard velocity messages feature as well.
It would be interesting to hear from a product manager as to whether it's possible to write firmware to place the reverberation module after the rotary simulation module in the effects chain.
I'm also interested in keyboard velocity messages feature as well.
- jazzspire
- Posts: 4
- Joined: 02 Oct 2013, 17:42
- Country:
- Has thanked: 2 times
- Been thanked: 1 time
- Your Nord Gear #1: Nord Stage EX
- Your Nord Gear #2: Nord C2D
Re: I wish the C2D ... (SW update?)
I just realized this is probably not possible. In order to determine a key's velocity, the time must be measured between the state change of its top and bottom switches. The MIDI message cannot be sent until the velocity is determined (after the bottom switch is closed).elseif wrote:
- sent keyboard velocity messages with the Keyboard Trig Mode set to High
I play LH bass. I split the lower manual and use the MIDI out of the half below the split to drive a ROMpler containing bass samples. Velocity messages are needed to get sample tonal variation. The rest of the keys are used for the B3 function.
I change this wish thusly: When the great (lower) manual is split into two sections, allow the Keyboard Trig Mode of the keys below the split to be set separately from the rest of the C2D's keys (upper manual and lower manual above the split).
- elseif
- Posts: 22
- Joined: 20 Jun 2015, 21:25
- Country:
- Has thanked: 0 time
- Been thanked: 4 times
- Your Nord Gear #1: Nord C2D
- Your Nord Gear #2: Nord Electro 4
Re: I wish the C2D ... (SW update?)
Non-causal key triggering - that's a feature.sweelinck wrote:I just realized this is probably not possible. In order to determine a key's velocity, the time must be measured between the state change of its top and bottom switches. The MIDI message cannot be sent until the velocity is determined (after the bottom switch is closed).
Yes. It is not just for midi but in general you would have to be able to predict the future to have the key velocity at the point in time when the high trigger point is reached. The key may accelerate to a higher velocity after that, for instance.
- elseif
- Posts: 22
- Joined: 20 Jun 2015, 21:25
- Country:
- Has thanked: 0 time
- Been thanked: 4 times
- Your Nord Gear #1: Nord C2D
- Your Nord Gear #2: Nord Electro 4
6 posts
• Page 1 of 1
Return to Nord C1 / C2 / C2D Organ Forum
Who is online
Users browsing this forum: No registered users and 17 guests